Відео

Well if you say so , thanks Sir. Hope it fixed your Fiskars.

@@Dentinvent Totally did, REALLY appreciate the help.

Nice work. Seems like many people are fixing this problem with the correct tutorials. Well done .

Hopefully you get yours going .

The spray paint was the same colour but the texture was not the same. The BMW original was more rubbery in texture . It still looked a lot better than peeling BMW paint. This was happening to all parts inside the car ( even the steering wheel).

@@Dentinvent thank you for that. yeah mine too. do you think plasti-dip would match better with OEM texture? my steering wheel trim is a little scratched up from previous owner. i was thinking sanding it down and spray painting it like you did or just wrapping it with vinyl.

The moisture should not easily get into the connector unless the robot is left in the pool for extended periods of time. Sealing the connector O rings with more silicone grease and sometimes the addition of a few slica gel balls will also help . So far no problems with corrosion. Of course copper and solder are not as good as gold . As long as your conductor rings are still conducting you should be fine. This fix really is for completely blown out areas and saved an expensive replacement.

That is great to hear. Thanks for watching and for your comment.

Try complete disassembly and deep cleaning of filters or try running it with no attachments or filters to see if it is a suction problem

@@Dentinvent you might have a blockage. clean the suction air ways and filters.

Thanks . Try using some magnified glasses and it really helps a lot especially anyone over 40 .

That may even help when taking the flap off . Good idea

If it is sucking in rubbish that shoots out the top , yes most likely the rapid drain flap opening up

Maytronics dolphin S series Best Video to show the mechanism of water Flow and Fault Finding ua-cam.com/video/exONiB3rUv0/v-deo.html

Thanks and Good thinking fellow Aussie but I think I did and actually could not see any difference. The only difference was the original one would keep bringing on the error even if it initially started working . You know how much patience my wife has if the thing I fix plays up ! Means don’t take any chances and just install a new pump .

Forensic analysis helps a lot more to people than .. just go buy a new one and heres how to replace it .. Its the next step as into why you Discovered the fact it needed replacing ... Good information is rare to find 👍👍

I’m all for forensic analysis. Honestly I did check with a multimeter on ohms and found no difference except one worked and one didn’t . I have about 5 multimeters ( one for each part of the house ).

My old pump which plays up seems to have nothing wrong with it .. It had 78ohms on each of the 3 coils inside and spins fine in test mode .. I went to buy one from a large appliance outlet here in Syd .. 4 days to order .OR He showed me one that LOOKED identical .. so I bought is and was going to fit it ... but as a precaution, I opened it up and noticed slightly less windings on the 3 Coils.. When I tested them they were only 45 ohms each .. I'm going to order the proper on and wait 4 days .. But I reassembled my old pump back in to give it another chance in test mode .. Every test cycle worked fine (Drain, Rinse, Spin etc) But it stops pumping and plays up "I deduce" only when it is submerged in the wash cycle at 40C° .. Ive since done 4 "Cold" Loads with my Old Pump reinstalled Successfully .. Something seems to be heat related on this 3yo Bosch Washer .. I'll get a new pump to see if it is the Pump .. Only other thing is "Could the Circuit board up top be affected by Heat ?"(rising) and sending the pump a skew frequency?? ... TBC ...

Thanks for the great comments. I did do some pauses because the string winding is as so complicated that I felt people needed it . Had a great day thanks to your compliments.

After that nice comment, I have to watch it again myself. Many thanks . I am planning to make more videos with some other models ( starting from a broken machine to complete diagnosis ).

Alex that is how they got the saying “Don’t get in a flap !” . Stay calm and so will your robot 😊.

What do you need ? Let me know

That’s such a great write up ! My wife said I was wasting my time when I said I wanted to fix the dishwasher . It is still working after about 15 years and best of all, I got to help many others out there with the same problem.

Update: dishwasher worked fine 2-3 times then E-24 popped up again. 😡 I remembered from your video that if the little white filter cover was not placed correctly, the code would return. Again, I stuck my head down there and sure enough, the little cover was not pressed in enough. I tucked him into bed but didn’t hear any click but noticed as I was returning the main filter back into place, the circle of the main filter caught and loosened the stem of the white impeller cover! So my head went back in, flashlight, and more force was placed to put both cover and filter carefully back into place, slowly. I believe in plucking out that cover stem so many times to check it, I probably bent the stem a little, causing this issue. Ran the machine on short cycle; no codes! Time will tell. Tell your wife your video has valuable world-wide status and saved people like me lots of cash I don’t have. Can wait to run the machine again…

Thanks Mark. I didn’t get a lot of views on this video but I’m sure it would have been higher if I was more famous .

Just look up eBay motorcycle gear indicator: Here is a cheap one www.ebay.com.au/itm/144744478485?mkcid=16&mkevt=1&mkrid=705-154756-20017-0&ssspo=nopt10tnqrc&sssrc=4429486&ssuid=PgJMlECQRru&var=&widget_ver=artemis&media=COPY

Thank you for the lovely comments. I am glad the video helped you. Hello back to Spain .

Always good to have both options of CarPlay and android auto in case someone gets in the car with a different phone .

@@Dentinvent nevermind, i thought you installed a double din without CarPlay/Android Auto since i didn't see a demo

The direction is controlled by the board in the motor . The power supply mainly just gives power and timer functions and can send signals to the motor to stay on floor etc. I think your problem is still in your motor box. Did you check the actual drive motors for current draw? I have found the actual current draw can affect start / stop of the robot . If only one of your drive motors is running, it will affect direction.

@@Dentinvent it is an M4 so only one drive motor. Board must not be proper one as from eBay seller.......ugh.

@@justfun-ij5xn Best way to get a replacement board is wait for a broken robot to come up that does not work but assess to make sure it has no water into the motor housing (work this out by the seller's description of how the robot died). Don't buy one off ebay as the seller makes ten times the price of a broken robot.

Seems like only certain batteries are sealed and some have hidden doors that can get into the cells. And yes, adding water will keep the battery going for many more years.

@@Dentinvent Thanks for doing this. Really appreciate it.

Glad you asked ! I’ve just completed another repair with the exact same problem . I could not get the pin higher so I extended it . I’ll have to make the video and show you how . It works perfectly now .

Oh I’d try silicone oil on the pin to see if it pops out more . If the white plastic looks melted it means high current has gone through that pin and it may not lift out more

Did anyone figure out how to make the pin spring up again?

I always thought both sides operate for the same time . I’ve taken many of the motors apart and I’m making videos on current draw and bearing changes. The robot in the video ended up stopping all the time . I took it apart and compared the two sides and one drew more current . I changed the bearing on the high craw motor and … it works like normal . Still working on that video of you want me to make it . I did note high draw current does make the robot stop completely.

If you open the motor it usually seals back well and you get a chance to check moisture inside it so that’s a bonus .

The original GT air has no quick release . The GT air 2 and Gt air 3 have quick release.

You should see my weak arthritic hands! Thanks for the comment. Happy blasting .

Kmart toasters do the job too and make great donor toasters for parts to fix these special toasters. I was going to see if I could spot weld the wire but haven’t tried it yet .

Can your tv send Bluetooth to link with the Megaboom?

Do you have the motor out ? If it runs with motor in the water but still stops, it will most likely be the drive bearing of the motor . Let me know and I’ll guide you .

Do you have the motor out ? If it runs with motor in the water but still stops, it will most likely be the drive bearing of the motor . Let me know and I’ll guide you .

@@Dentinvent thank you. Ill check it out tmw. I appreciate it.

I had to google and Rocko is not supposed to have a real Australian accent .

@@Dentinvent thanks for the tip mate. I’ll be trying this out soon.

That makes me happy . Thanks for the comment

Thanks for your comment. I know of people who get the mister minute place to change the battery and it ends up costing them a lot of money for something they could have done for the price of a battery .

From memory , the shroud just clips on . The clips also tend to break off easily so be careful. You can see the clips at about 1 minute 50 secs on the video .

Hope the video did help you with your replacement. Yes designed so that it is harder to change but they assume the average person is not doing their own drain pump change.

Many thanks back to you and I sincerely hope the video helps you to fix your robot.

Sorry man , The top part is taped on and screws taken out and the front panel drops off . This is to allow you to get under the front . The tape is so that the whole control section does not fall off as it has a heap of wires inside the control section . The front panel needs to be removed to get under the front of the dishwasher as the panel covers the drain pump . In the next scene you can see the front panel is missing .

Hey thanks. All the wiring was attached to the door panel so I couldn’t take it all the way off. I ended up pulling it up 6 inches and taping it in place while I replaced the pump and it worked well. Thanks again for the video.

Yes and it worked well. No wheels fell off and they were quite well balanced .

Yes and it worked well. No wheels fell off and they were quite well balanced .

Did you change your pump ? Sometimes the pump is the problem making the control board not work.

@@Dentinvent no I didn’t change the pump. The eco mode work fine the last time and didn’t trigger any error code.

I think later the error may come back . The machine maybe sensing an upcoming problem. It’s sort of like a toothache… you hope it goes away .

No worries . It really does help to make your machine work properly.

Finally someone likes it ! Thanks . I made a few of these and the stands were worth more than the old TVs. I think I have too many tools.

to sum up the lights showing: -The red car on the hoist (everytime I start the car) followed by -red service light and -constant red handbrake light

If you get really stuck , get the old brake sensor and short the two wires with it installed in the car and reset the computer and then reinstall the new sensor. Shorting the wires will let you reset the bmw computer . Let me know how you go .

If you get really stuck , get the old brake sensor and short the two wires with it installed in the car and reset the computer and then reinstall the new sensor. Shorting the wires will let you reset the bmw computer . Let me know how you go .

@@Dentinvent thanks for the tip! i'll let you know once i get to try it

If you look carefully how I take the drawers out ( use a bent feeler gauge ) you can see that there is a tab that stops the drawers coming right out . Take your drawer off then you can see the tab . Bend the tab out a bit and when you lock the drawer back in , it will not slip out .

@@Dentinvent I've pulled them out before, using the metal piece from a file folder, but some don't have that...like it broke off possibly. Is it possible to weld a lil nob/stop thing on it?? Or possibly cut a new tab? Thank you for responding, greatly appreciated.

Hopefully that repair manages to withstand the bending. Seems like many of these aftershokz break .

@@Dentinvent the internal head band is acting as a paper clip

Which elastic bands do you mean? The elastic band caught in my impeller was a normal rubber band that went through the wash and tied up the impeller .

Which elastic bands do you mean? The elastic band caught in my impeller was a normal rubber band that went through the wash and tied up the impeller .

Which elastic bands do you mean? The elastic band caught in my impeller was a normal rubber band that went through the wash and tied up the impeller .

Which elastic bands do you mean? The elastic band caught in my impeller was a normal rubber band that went through the wash and tied up the impeller .

Yes looks like everyone makes a mess unless they are ocd

Thanks . I think Toyota should put that in their car manual.

You are lucky yours was in good condition. At least you know how to take the drawers out now.